### calculation of dBm in Milliwatt for wireless Acess Points WiFI

**power of wireless Acess Points WiFi**

**dBm** (sometimes **dBmW** or Decibel-milliwatts) is an abbreviation for the power ratio in decibels (dB) of the measured power referenced to one milliwatt (mW). It is used in radio, microwave and fiber optic networks as a convenient measure of absolute power because of its capability to express both very large and very small values in a short form. Compare dBW, which is referenced to one watt (1000 mW).

Since it is referenced to the watt, it is an absolute unit, used when measuring absolute power. By comparison, the decibel (**dB**) is a dimensionless unit, used for quantifying the ratio between two values, such as signal-to-noise ratio.

In audio and telephony, dBm is typically referenced relative to a 600 ohm impedance,^{[1]} while in radio frequency work dBm is typically referenced relative to a 50 ohm impedance.^{[2]}

## Unit conversions and calculation of dBm in Milliwatt for wireless Acess Points WiFI

A power level of 0 dBm corresponds to a power of 1 milliwatt. A 3 dB increase in level is approximately equivalent to doubling the power, which means that a level of 3 dBm corresponds roughly to a power of 2 mW. For each 3 dB decrease in level, the power is reduced by about one half, making −3 dBm correspond to a power of about 0.5 mW.

To express an arbitrary power *P* in watts as *x* in dBm, or vice versa, the following equivalent expressions may be used:

and

where *P* is the power in W and *x* is the power level in dBm. Below is a table summarizing useful cases:

Power level | Power | Notes |
---|---|---|

80 dBm | 100 kW | Typical transmission power of FM radio station with 50-kilometre (31 mi) range |

62 dBm | 1.588 kW = 1,588 W | 1500 W is the maximum legal power output of a U.S. ham radio station.^{[3]} |

60 dBm | 1 kW = 1,000 W | Typical combined radiated RF power of microwave oven elements |

50 dBm | 100 W | Typical thermal radiation emitted by a human body
Typical maximum output RF power from a ham radio HF transceiver |

40 dBm | 10 W | Typical PLC (Power Line Carrier) transmit power |

37 dBm | 5 W | Typical maximum output RF power from a handheld ham radio VHF/UHF transceiver |

36 dBm | 4 W | Typical maximum output power for a Citizens' band radio station (27 MHz) in many countries |

33 dBm | 2 W | Maximum output from a UMTS/3Gmobile phone (Power class 1 mobiles)
Maximum output from a GSM850/900 mobile phone |

30 dBm | 1 W = 1,000 mW | Typical RF leakage from a microwave oven^{[citation needed]}
DCS or GSM 1,800/1,900 MHz mobile phone. EIRP IEEE 802.11a (20 MHz-wide channels) in either 5 GHz Subband 2 (5,470–5,725 MHz) provided that transmitters are also IEEE 802.11h-compliant, |

29 dBm | 794 mW | |

28 dBm | 631 mW | |

27 dBm | 500 mW | Typical cellular phonetransmission power
Maximum output from a UMTS/3G mobile phone (Power class 2 mobiles) |

26 dBm | 400 mW | |

25 dBm | 316 mW | |

24 dBm | 251 mW | Maximum output from a UMTS/3G mobile phone (Power class 3 mobiles)
1,880–1,900 MHz DECT (250 mW per 1,728 kHz channel). EIRP for Wireless LAN IEEE 802.11a (20 MHz-wide channels) in either the 5 GHz Subband 1 (5,180–5,320 MHz) or U-NII-2 & -W ranges (5,250–5,350 MHz & 5,470–5,725 MHz respectively). The former is EU only, the latter is US only. |

23 dBm | 200 mW | EIRP for IEEE 802.11n Wireless LAN 40 MHz-wide (5 mW/MHz) channels in 5 GHz subband 4 (5,735–5,835 MHz, US only) or 5 GHz subband 2 (5,470–5,725 MHz, EU only). Also applies to 20 MHz-wide (10 mW/MHz) IEEE 802.11a Wireless LAN in 5 GHz Subband 1 (5,180–5,320 MHz) if also IEEE 802.11h compliant (otherwise only 3 mW/MHz → 60 mW when unable to dynamically adjust transmission power, and only 1.5 mW/MHz → 30 mW when a transmitter also cannot dynamically select frequency). |

22 dBm | 158 mW | |

21 dBm | 125 mW | Maximum output from a UMTS/3G mobile phone (Power class 4 mobiles) |

20 dBm | 100 mW | EIRP for IEEE 802.11b/g Wireless LAN 20 MHz-wide channels in the 2.4 GHz ISM band(5 mW/MHz).
Bluetooth Class 1 radio. Maximum output power from unlicensed AM transmitter per U.S. Federal Communications Commission (FCC) rules 15.219. |

19 dBm | 79 mW | |

18 dBm | 63 mW | |

17 dBm | 50 mW | |

15 dBm | 32 mW | Typical Wireless LAN transmission power in laptops. |

10 dBm | 10 mW | |

7 dBm | 5.0 mW | Common power level required to test the Automatic Gain Control circuitry in an AM receiver. |

6 dBm | 4.0 mW | |

5 dBm | 3.2 mW | |

4 dBm | 2.5 mW | Bluetooth Class 2 radio, 10 m range |

3 dBm | 2.0 mW | More precisely (to 8 decimal places) 1.9952623 mW |

2 dBm | 1.6 mW | |

1 dBm | 1.3 mW | |

0 dBm | 1.0 mW = 1,000 µW | Bluetooth standard (Class 3) radio, 1 m range |

−1 dBm | 794 µW | |

−3 dBm | 501 µW | |

−5 dBm | 316 µW | |

−10 dBm |
100 µW |
Typical maximum received signal power (−10 to −30 dBm) of wireless network |

−20 dBm | 10 µW | |

−30 dBm | 1.0 µW = 1,000 nW | |

−40 dBm | 100 nW | |

−50 dBm | 10 nW | |

−60 dBm | 1.0 nW = 1,000 pW | The Earth receives one nanowatt per square metre from a magnitude +3.5 star^{[5]} |

−70 dBm | 100 pW | |

−73 dBm | 50.12 pW | "S9" signal strength, a strong signal, on the S-meter of a typical ham or shortwave radio receiver |

−80 dBm | 10 pW | Typical range (−70 to −90 dBm) of wireless received signal power over a network (802.11 variants) |

−100 dBm | 0.1 pW | |

−111 dBm | 0.008 pW = 8 fW | Thermal noise floor for commercial GPS single channel signal bandwidth (2 MHz) |

−127.5 dBm | 0.178 fW = 178 aW | Typical received signal power from a GPS satellite |

−174 dBm | 0.004 aW = 4 zW | Thermal noise floor for 1 Hz bandwidth at room temperature (20 °C) |